View HX1_4270225.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EW N
28 August 2007
Radiometrix
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233
HX1 (300mW)
300mW VHF Narrow Band FM 300 W Transmitter
The special HX1 transmitter modules offer a 300mW RF output VHF data link in Radiometrix SIL standard pinout and footprint. This makes the HX1 ideally suited to those low power applications where existing narrow band and wideband transmitters provide insufficient range. Together with the matching NRX1 or BiM1R receiver a one-way radio data link can be achieved over a distance up to 10km+ with suitable choice of data rate and antennas.
Figure 1: HX1-169.4125-3-5V
Features
* * * * * * Standard frequency: 169MHz band Other frequencies from 120MHz to 180MHz Data rates up to 3kbps Usable range over 10km Fully screened Low power requirements
The HX1 is a narrow band radio transmitter module for use in long range data transfer applications at ranges up to 10kilometres. HX1 transmitter circuit is the BiM1T transmitter circuit in the TX1 pin-out with slightly enlarged dimension to accommodate extra Power Amplifier circuit to produce 300mW RF output and available for operation on 169MHz European licence exempt frequency band.
Applications
* * * * * * * * * * Tracing and asset tracking systems Meter reading systems Industrial telemetry and telecommand Data loggers In-building environmental monitoring and control Social alarms High-end security and fire alarms Automatic Position Reporting System (APRS) DGPS systems Vehicle data up/download
Technical Summary
* * * * * * Transmit power: 300mW (24.7dBm) Operating frequency: 169.4125MHz, 169.5625MHz Supply: 5V (regulated) Current consumption: 140mA nominal transmit Data bit rate: 3kbps max. Size: 43 x 15 x 5mm
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 1
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Figure 2: HX1 block diagram
Page 2
Functional description
The HX1 transmitter consists of a frequency modulated Voltage Controlled Crystal Oscillator (VCXO) feeding a frequency doubler with two stage amplifier and RF filter. Final Power Amplifier stage is factory pre-set to appropriate band power level. Operation can be controlled by the EN (Enable) line, the transmitter achieving full RF output typically within 5ms of this line being pulled high. The RF output is filtered to ensure compliance with the appropriate radio regulations and fed to the 50 antenna pin.
User interface
43mm
5mm
14.5mm
HX1(300mW)
pin spacing: 2.54 mm 15.24 mm 1 = RF gnd 2 = RF out 3 = RF gnd 4 = En 5 = Vcc 6 = 0V 7 = TXD
1
2
3
4
5
6
7
7 holes of 0.7 mm dia. pin spacing 2.54 mm
Figure 3: HX1 pin-out and dimension TX1H pin 1, 3 2 4 5 6 7 Name RFgnd RF out EN VCC 0V TXD Function RF Ground 50 RF output to the antenna Pull high to enable Transmitter 5V regulated DC power supply Ground DC coupled input for 5V CMOS logic. Rin = 100k
Note: Pinout and footprint as TX1. (but PCB is longer)
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 3
Absolute maximum ratings
Exceeding the values given below may cause permanent damage to the module. Operating temperature Storage temperature -10C to +60C -30C to +70C
Performance specifications:
(Vcc = 5V / temperature = 20C unless stated) pin Supply Supply voltage TX Supply current RF RF power output Spurious emissions Adjacent channel TX power Frequency accuracy FM deviation (peak) Antenna pin impedance RF centre frequency Channel spacing Number of channels Baseband Modulation bandwidth @ -3dB TXD input level (logic low) TXD input level (logic high) Dynamic timing TX select to full RF 4 4 2 2 min. +23.7 -2.5 2.5 0 typ. 5 140mA +24.7 -40 -37 0 3.0 50 169.4125 169.5625 25 1 0 5.0 5 max. +25.7 +2.5 3.5 5 units V mA dBm dBm dBm kHz kHz MHz MHz kHz 1 2 3 4 5 5 notes
2
6 6
kHz V V ms
6 7 7
Notes: 1. Measured into 50 resistive load 2. For 1kbps Manchester encoded; the data bit rate is limited to 3kbps NRZ max. to meet adjacent channel power specification. 3. Total over full supply and temperature range 4. With 0V - 5.0V modulation input 5. Other VHF 120-180MHz by special order 6. 5V CMOS compatible 7. To achieve specified FM deviation
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 4
Applications information
Expected range
Predicting the range obtainable in any given situation is notoriously difficult since there are many factors involved. The main ones to consider are as follows: * * * * * Type and location of antennas in use Type of terrain and degree of obstruction of the link path Sources of interference affecting the receiver "Dead" spots caused by signal reflections from nearby conductive objects Data rate and degree of filtering employed
The following are typical examples - but range tests should always be performed before assuming that a particular range can be achieved in a given situation: Data rate 1.2kbps 10kbps 10kbps 10kbps Note: Tx antenna half-wave half-wave helical helical Rx antenna half-wave half-wave half-wave helical Environment rural/open rural/open urban/obstructed in-building Range 10-15km 3-4km 500m-1km 100-200m
The figure for 1.2kbps assumes that the receiver bandwidth has been suitably reduced by utilising an outboard sallen-key active audio filter and data slicer or similar arrangement.
Antennas
The choice and positioning of transmitter and receiver antennas is of the utmost importance and is the single most significant factor in determining system range. The following notes are intended to assist the user in choosing the most effective antenna type for any given application. Integral antennas These are relatively inefficient compared to the larger externally-mounted types and hence tend to be effective only over limited ranges. They do however result in physically compact equipment and for this reason are often preferred for portable applications. Particular care is required with this type of antenna to achieve optimum results and the following should be taken into account: 1. Nearby conducting objects such as a PCB or battery can cause detuning or screening of the antenna which severely reduces efficiency. Ideally the antenna should stick out from the top of the product and be entirely in the clear, however this is often not desirable for practical/ergonomic reasons and a compromise may need to be reached. If an internal antenna must be used try to keep it away from other metal components and pay particular attention to the "hot" end (i.e. the far end) as this is generally the most susceptible to detuning. The space around the antenna is as important as the antenna itself. 2. Microprocessors and microcontrollers tend to radiate significant amounts of radio frequency hash which can cause desensitisation of the receiver if its antenna is in close proximity. The problem becomes worse as logic speeds increase, because fast logic edges generate harmonics across the VHF range which are then radiated effectively by the PCB tracking. In extreme cases system range may be reduced by a factor of 5 or more. To minimise any adverse effects situate antenna and module as far as possible from any such circuitry and keep PCB track lengths to the minimum possible. A ground plane can be highly effective in cutting radiated interference and its use is strongly recommended.
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 5
The following types of integral antenna are in common use: Quarter-wave whip. This consists simply of a piece of wire or rod connected to the module at one end. At 169MHz the total length should be 421mm from module pin to antenna tip including any interconnecting wire or tracking. Because of the length of this antenna it is almost always external to the product casing. Helical. This is a more compact but slightly less effective antenna formed from a coil of wire. It is very efficient for its size, but because of its high Q it suffers badly from detuning caused by proximity to nearby conductive objects and needs to be carefully trimmed for best performance in a given situation. The size shown is about the maximum commonly used at 169MHz and appropriate scaling of length, diameter and number of turns can make individual designs much smaller. Loop. A loop of PCB track having an inside area as large as possible (minimum about 5cm2), tuned and matched with 2 capacitors. Loops are relatively inefficient but have good immunity to proximity detuning, so may be preferred in shorter range applications where high component packing density is necessary. Integral antenna summary: whip *** *** * ** helical ** ** *** * loop * * ** ***
Ultimate performance Ease of design set-up Size Immunity to proximity effects
421mm @ 169MHz
RF
Whip antenna
wire, rod, PCB track or a combination of these length(mm) = 71250 / freq(MHz)
RF
Helical antenna
35-40 turns wire spring length 120mm, dia 10mm trim wire length or expand coil for best results
RF Ctune C match RF GND
track width = 1mm 2 min. area 500mm capacitors may be variable or fixed (values depend on loop dimensions)
Loop antenna
Figure 4: integral antenna configurations
External antennas These have several advantages if portability is not an issue, and are essential for long range links. External antennas can be optimised for individual circumstances and may be mounted in relatively good RF locations away from sources of interference, being connected to the equipment by coax feeder. Helical. Of similar dimensions and performance to the integral type mentioned above, commerciallyavailable helical antennas normally have the coil element protected by a plastic moulding or sleeve and incorporate a coax connector at one end (usually a straight or right-angle BNC type). These are compact
Radiometrix Ltd., HX1 high power transmitter data sheet Page 6
and simple to use as they come pre-tuned for a given application, but are relatively inefficient and are best suited to shorter ranges. Quarter-wave whip. Again similar to the integral type, the element usually consists of a stainless steel rod or a wire contained within a semi-flexible moulded plastic jacket. Various mounting options are available, from a simple BNC connector to wall brackets, through-panel fixings and magnetic mounts for temporary attachment to steel surfaces. A significant improvement in performance is obtainable if the whip is used in conjunction with a metal ground plane. For best results this should extend all round the base of the whip out to a radius of 300mm or more (under these conditions performance approaches that of a half-wave dipole) but even relatively small metal areas will produce a worthwhile improvement over the whip alone. The ground plane should be electrically connected to the coax outer at the base of the whip. Magnetic mounts are slightly different in that they rely on capacitance between the mount and the metal surface to achieve the same result. A ground plane can also be simulated by using 3 or 4 quarter-wave radials equally spaced around the base of the whip, connected at their inner ends to the outer of the coax feed. A better match to a 50 coax feed can be achieved if the elements are angled downwards at approximately 30-40 to the horizontal.
(421mm long @ 169MHz)
1/4-wave whip
1/4-wave whip
Metal ground plane
1/ (3-4 4w , eq av u e all ra y di s p al a el ce em d ) en ts
30 -40
de g.
50 coax feed
50 coax feed
Fig.5: Quarter wave antenna / ground plane configurations Half-wave. There are two main variants of this antenna, both of which are very effective and are recommended where long range and all-round coverage are required: 1. The half-wave dipole consists of two quarter-wave whips mounted in line vertically and fed in the centre with coaxial cable. The bottom whip takes the place of the ground plane described previously. A variant is available using a helical instead of a whip for the lower element, giving similar performance with reduced overall length. This antenna is suitable for mounting on walls etc. but for best results should be kept well clear of surrounding conductive objects and structures (ideally >1m separation). 2. The end-fed half wave is the same length as the dipole but consists of a single rod or whip fed at the bottom via a matching network. Mounting options are similar to those for the quarter-wave whip. A ground plane is sometimes used but is not essential. The end-fed arrangement is often preferred over the centre-fed dipole because it is easier to mount in the clear and above surrounding obstructions. Yagi. This antenna consists of two or more elements mounted parallel to each other on a central boom. It is directional and exhibits gain but tends to be large and unwieldy - for these reasons the yagi is the ideal choice for links over fixed paths where maximum range is desired.
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 7
Module mounting considerations The modules may be mounted vertically or bent horizontal to the motherboard. Good RF layout practice should be observed. If the connection between module and antenna is more than about 20mm long use 50 microstrip line or coax or a combination of both. It is desirable (but not essential) to fill all unused PCB area around the module with ground plane.
Variants and ordering information The HX1 transmitter is manufactured in the following variants as standard: HX1-144.390-3 HX1-144.800-3 HX1-168.360-3 HX1-169.4125-3 HX1-169.5625-3 HX1-173.225-3 Other variants can be supplied to individual customer requirements at frequencies from 120MHz to 180MHz
Matching Receivers: NRX1-xxx.xxx-10 (SIL footprint) BiM1R-xxx.xxx-10 (DIL footprint)
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 8
Radiometrix Ltd
Hartcran House 231 Kenton Lane Harrow, Middlesex HA3 8RP ENGLAND Tel: +44 (0) 20 8909 9595 Fax: +44 (0) 20 8909 2233 sales@radiometrix.com www.radiometrix.com Copyright notice
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner.
Limitation of liability
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications. The Intrastat commodity code for all our modules is: 8542 6000
R&TTE Directive
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular equipment. Further details are available on The Office of Communications (Ofcom) web site: http://www.ofcom.org.uk/radiocomms/ifi/ Information Requests Ofcom Riverside House 2a Southwark Bridge Road London SE1 9HA Tel: +44 (0)845 456 3000 or 020 7981 3040 Fax: +44 (0)20 7783 4033 information.requests@ofcom.org.uk European Radiocommunications Office (ERO) Peblingehus Nansensgade 19 DK 1366 Copenhagen Tel. +45 33896300 Fax +45 33896330 ero@ero.dk www.ero.dk
Radiometrix Ltd.,
HX1 high power transmitter data sheet
Page 9

▲Up To Search▲

Price & Availability of HX1

	To Download HX1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .